The development of purpose, verbal stimulation initiatives, the mood for improving health and addictions... Assistance in the development of these and other qualities will have the device protected by the patent of Russian Federation № 2109523. The design is submitted to the readers.
The attractiveness of the development attached as the availability of the instrument a home workshop, and proven method of self-hypnosis on Cue with using elements of neuro-linguistic programming, lying in the basis of operation of the device. With regard to the effectiveness of the device, it depends on many factors, including the duration of the verbal impact. The recommended period of continuous influence of the formula of suggestion directed, for example, for high-quality preparation for the exam, from 10 to 30 days.
A circuit diagram of the device (volume control sound Converter conventionally not shown) (click to enlarge)
As can be seen from the circuit diagram, keychain-a mobilizer abilities includes dual-frequency master oscillator DD1.1-DD1.3, multi-bit binary counter DD2, DD3, reprogrammable storage device (ROM) DD4, a digital to analogue Converter (DAC) R7-R14 and the output stage DD1.4, load which is the transducer BQ 1 type CP-5 or CP-22.
When the power source of supply through a capacitor C4 and a resistor R6 current begins to flow of charge and to install (reset) chip DD2, DD3 to its original state. The output potential of the high order counter (pin 13
DD2.2) becomes equal to a logical "0" and opens DD1.3 (pin 9) and ROM (pins 20 and 22). Through the diode VD1 input logic element DD1.3 is disconnected from o 6 DD1.2. Generator (DD1.2 and DD1.3) clock pulses are generated with a frequency-dependent capacitor C2 and resistors R3, R4. Preference given 16,11 or 8 kHz. Continuous adjustment of the frequency is variable resistor R4.
Now proceed to the work of the counter logic elements DD2.1 and with DD3 clock differential chain СЗR5. And since its output level connected to the ROM, then extract the relevant information - parts of the verbal formula of suggestion, recorded in advance in the form codes in an electronic memory.
Digital to analog Converter resistors R7-R14 transforms code combination in the analog signal. For matching DAC with sound the inverter serves as the output stage DD1.4 operating in a linear mode. Moreover, for noise reduction of the latter is provided with a low pass filter (С5R15) with frequency cut about 16 kHz.
After using the whole capacity of the ROM (32768 samples) read cycle and decoding information is repeated, if the jumper S1 is connected to pin 13 DD2.2 (two-time playback of the verbal formula). When connecting the same to S1 output 12 DD2.2 vosema hear one phrase, and to the conclusion of the 14-four times. A logical "1" appearing at the respective output (12, 13 or 14) DD2.2, locks the ROM (vyv. 20, 22) and the output stage DD1.4 (vyv. 13) reducing power consumption in pause mode and disconnects the DD1.3 (vyv. 9).
On the elements DD1.1 and DD1.2 begins to run the master oscillator. Its frequency, determined by the values of C1, R1, R3, R4, is a popular option when setting a time interval between phrases of suggestion. The duration the pause will be one- , two - or four-depending on the connection jumper S1 to the terminals 12,13 or 14 logic element DD2.2.
Strictly speaking, the pause continues until a logical "0" on the output connected to the jumper S1, then the duty cycle (play + pause) repeats. The duration of the same one-time playback is determined by selecting the frequency of the master oscillator, operating on the elements DD1.2 and DD1.3 chip CLE, and is configured by the capacitor C2 together with the resistors RЗ, R4. Wherein R4 is used primarily to adjust skorogovorki". It is recommended that this parameter at the top (the scheme) the position of the slider the variable resistor corresponds to 120 and when you right - 480 words per minute.
Keychain-a mobilizer abilities: 1 - the tapping screw (2 PCs); 2 - battery terminal (2 pieces); 3 - battery D-0,06 (4 PCs); 4 - volume control transducer; 5 - synthetic ring tape (to remove the ROM chips from the panel); 6 - the ROM chip s; 7 - battery compartment cover and replace the ROM; 8 - pin; 9 - ring pendants keychain; 10 - housing 11 - panel ROM chips; 12 - audio Converter SN-W; 13 - housing cover; 14 - sided printing fee; 15 - printed circuit; 16 - regulator "skorogovorki" with built-in power switch; 17 - pin electrorama (for recharging batteries, 2 PCs.)
Option two-sided printed circuit Board with the symbol on it places placement of IC, regulator "skorogovorki and electrolytic condenser (click to enlarge)
To reduce the size of the product you can go for the replacement of R4 and R3 one a constant resistor whose value should be selected with the emphasis on normal "storageformat" 120 words per minute. For setting it is necessary to include in the chain power milliammeter to detect and elapsed playing time suggestible phrase. When the operating frequency of 16 kHz and the current is "speaking" about 9 mA (while in pause mode about 3 mA) duration one-time playback of the phrase should be within 2 C. For a frequency of 11 (or 8) kHz at constant other conditions guidance can serve as the stopwatch with 3 (or 4). Preference to those frequencies because they are used in computer "sound" technologies.
The pause duration is configured by the capacitor C1 and resistor R1. Alignment runs on milliammeter reading and stopwatch with an indispensable account jumper S1 is directly related to the frequency of the work cycle. Recommended guidelines: the 4-time repetition and pause duration of about 20 min.
The sound quality of the formula of suggestion depends on the synchronization of the counter (DD2.1, DD2.2 and DD3) differential chain C3R5. Naturally, affects digital to analog Converter. The sound of the formulas of suggestion is more "clean", if the resistance included in the DAC resistors meet (as of increase their numbers from R7 to R14) number of values, decreasing with the division ratio 2.
Phrase (verbal formulas) suggestions should be concise and motivating categorically, without the use of the particle "not". Instead of flimsy stamped "NO SMOKING" signs should be used positively perceived word-orders "QUIT SMOKING" or "AVERSION TO SMOKING". When preparing formula suggestions it should be as precise as possible is the ultimate goal, not forgetting about the mood in her the speedy achievement. For example, effectively seen such inspiring action phrases like "WELL EXAMS", "REPLACE "DRUGS" SPORTS", "TO NORMALIZE BLOOD PRESSURE."
Embedded ROM special programmer, the file which is prepared with by using a personal computer (PC) with the sound card. So, in wav format 16 kHz (8 bits), you can record sound with a duration of 2 s, using wav 11 kHz (8 bits) will provide you three, a wav 8 kHz (8 bits) - four-second recording.
When creating files, apply sound card driver, software menu and standard technology user's PC. First, you select the desired format. For example, wav 11 kHz (8 bits). By the way, on the same 11 kHz should work keychain-a mobilizer of abilities when it plays formula suggestions with normal speed, i.e. with a period of a single reading ROM duration 3 C. Preparation of files is greatly simplified if you use specialized audio programs, for example, Cool Edit 1.50.
The effectiveness of the device is significantly increased if formula suggestion sounds on musical background. Therefore, when preparing the file for the programmer is recommended mixing: verbal entry plus fragments of any euphonic works.
To do this, through the microphone or line input to record on the PC disk passage favourite pieces of music with a duration of 30-60. Then made from the recording of "the mouse" allocate on computer the waveform 9 with plots which after listening to copying via the clipboard to a new file. Cut out selected and verifying the ear the most appropriate, not exceeding the total duration of the sound with 3, translate (again via the clipboard) received slices of the future of music in the following file with assignment it's just a catchy name-the numbers: for example, fragmnt1.wav. Similarly prepare and retain in the directory that you create on the PC disk, about seven future musical accompaniment (from fragmnt1.wav to fragmnt7.wav), with a different rhythm and tonality.
Then move to the file with the formula suggestion. Text lash out in accordance with presented recommendations and recording through the MIC input of the sound card of the PC in the selected format wav 11 kHz (8 bits). Honed to perfection the phrase say 3-5 times with small (to facilitate selection of waveforms) intervals. To obtain the desired tone when writing formulas of suggestion it is advisable to mentally addressed to recite the words of the man lying on the couch. Select the most soulful and short phrases.
Removing computer waveform "empty" areas and making sure that the total duration does not exceed 3, is transferred via the clipboard almost finished formula suggestion in a new file by assigning the appropriate (for example, "protivokorabelnaja" bros_kur.wav) name for quick recognition.
Directly to enter into the programmer device firmware ROM - preparing a third file. It is created by mixing the previous terms already recorded on the PC: formula suggestions and pre-screened melodic fragment. It is at this stage strive to achieve the harmony, in which the rhythm and tone of music to the maximum match the meaning of the words, and the sound level by about half less the volume of the phrase. The mixed file stored with assignment of the easily recognizable name, for example, bros~kur.wav.
"Firmware" ROM is performed in strict accordance with the instructions to the programmer. The signal from the file prepared for sewing, must ensure the playback volume level of a whisper.
If there are neither instructions nor a programmer, nor even a simple PC, one thing remains: to contact any of the firms that service the cash cars. The equipment there, as a rule, good, and experienced professionals. So there is every reason to hope that the "firmware" ROM will be done well.
"Stitched" ROM soldered to the bilateral circuit Board with foiled fiberglass.
Author: A. Soloviev